How To Repair Broken Glasses

Download Article

Download Article

Breaking your eyeglasses can exist frustrating, and you might not ever be able to replace them right away. Whether you scratched the lense, lost a screw, or broke the span, you can repair your eyeglasses yourself to hold you over until you are able to get a new pair.

1. i

   Get your materials in place. Y'all'll need a thread, needle, drill, sandpaper, superglue, painter's stir stick, rubber bands, waxed paper, cotton swabs, alcohol or boom polish remover and a hobby pocketknife.

2. 2

   Clean and sand the broken pieces. Use sandpaper to clean and rough upward the cleaved area to exist glued. Swab the area with some rubbing booze or boom smooth remover to gear up the surface.

3. 3

   Secure the two pieces together. Cut a piece of a painter'southward wooden stir stick to fit betwixt the temples (aka, the side pieces) of your glasses. Cover your lenses with wax newspaper to forbid scratching so wrap a condom band over one end of the stick and secure it to your spectacles. Do the same on the other finish.

   • Line the two halves up carefully and be sure the rubber bands are holding things firmly in place. If information technology wasn't a clean break and there are some gaps, line the pieces up as best you can taking pains to ensure there are some definite points of contact.^[three]

4. 4

   Glue. Fill up the joint at the break with gum; utilise enough to secure the bridge merely not so much that the gum runs out. Squeeze out the gum slowly and neatly to avoid bubbles. As you fill in the joint, be sure that in that location are no gaps or voids. Use the side of a cotton swab to gently clean up whatsoever excess glue; swab it up before it has a hazard to dry and get tacky. Prepare the glasses aside for at least an hour then the glue tin can dry completely.

5. v

   Drill two holes. Choose a small drill bit appropriate for the thickness of your eyeglass frames. Take your hobby knife and dig out pilot holes on either side of the newly repaired joint. Place your spectacles down on a soft cloth that'southward been laid on a tabular array tiptop and carefully drill a pigsty on each side of the break. The holes must exist parallel and so they can be used to wrap a band of thread effectually the core joint.^[iv]

6. six

   Run up a tension band in identify. Use a fine needle and iv to six anxiety of thread that matches the color of your eyeglass frames to "stitch" the two sides of the repair together for added force. Laissez passer the needle and thread through the two holes every bit many times as you lot can taking care not to pull too hard and put stress on the newly repaired joint. End when there'due south no more room. Fill the drilled holes with glue, soaking the thread and blotting up any excess with a cotton swab. Trim the edges of the thread and allow the glue to dry out for at to the lowest degree an hour.

7. 7

   Add a wrap. If you desire to give extra strength to your repair, you lot tin add this additional step to your process. Practice not trim the edges of the thread as above. Instead, later on your glue has dried, take the remaining thread from 1 side and wrap it effectually the bridge of your glasses from front to back. Make your wrap every bit peachy as possible; some criss-crossing may be unavoidable, but do your all-time to prevent the wrap from looking beefy. Leave a brusque end to be trimmed later. Soak the wrap with glue and allow it dry for 10-15 minutes. Have the thread from the other side of your spectacles and wrap information technology around the bridge in the opposite direction (dorsum to front). Soak the new wrap in glue and let it cure for a couple of minutes before snipping off the two loose ends. Set your glasses aside for 24 hours before wearing.

Advert

1. 1

   Boil water. Fill a small pot with water and set the flame to "high." Considering you're going to employ heat for this repair, the frames of your glasses must exist plastic for it to work.

2. 2

   Cook the plastic. Once the water is boiling, agree the broken edges of the spectacles over the pot and close enough for the rut to soften the edges.

3. 3

   Insert a pin. Push a short pivot into 1 edge and then button the other border onto the pin. While the plastic is nevertheless hot, smooth it over the pin. ^[v]

   • Never put plastic eyeglass frames straight over a flame.

Advertizing

1. i

   Utilise an eyeglass repair kit. Eyeglass repair kits are readily bachelor at drugstores and contain everything y'all need to brand a repair--screws, a tiny screwdriver and sometimes a magnifying glass. A newer version of the kit contains longer screws meant to be easier to handle. Y'all insert the screws into the hinges, screw them in and and then "snap off" the lesser of the screw to fit the size of the hinge.

   • If y'all're finding it difficult to line up the hinges on your temple piece and front slice, information technology could because a hinge mechanism within the temple piece swivel is holding it back. To right this, use the hook end of a newspaper clip, insert it through the temple hinge hole and gently pull it out. To proceed the hinge pigsty in place, insert a second paperclip upright and into the "gap" created when yous pulled out the swivel pigsty. Line upward the forepart slice and temple slice holes and insert and tighten the screw. When you're finished, remove the paperclip from the gap and the hinge pigsty will slide back into place creating a firm fit for your spectacles. ^[6]

2. 2

   Endeavour a toothpick. When a screw falls out of the hinge that holds the front and temple pieces of your spectacles together, use a toothpick to temporarily accept the place of the screw. Line up the temple swivel holes with the front holes and push a wooden toothpick through them as far as information technology will get. Pause or prune off the excess.^[7]

3. 3

   Substitute with a wire. Strip the paper off of a twist necktie (the kind that come up on a bag of bread). Line up the hinge holes and thread the twist-tie wire through them. Twist the wire in place until the temple feels secure. Cut off the edges of the wire so you don't get scratched. You lot tin also use a small safety pin (the ones that are sometimes used with clothing cost tags). Insert the pin through the holes to hold the side in place.

Advert

1. 1

   Utilise baking soda and h2o. Commencement, wipe off both your lenses with a microfiber cloth. Side by side, mix 1 teaspoon (4.9 mL) of water with ane tablespoon (fifteen mL) of baking soda until information technology forms a paste-similar consistency. Then, apply the paste to your lenses and gently scrub your lenses with the substance. After, rinse your spectacles with water to wash off the baking soda mixture. This volition likely be all you need to remove the scratches!^[8]

2. two

   Utilize a household cleaner. Abrasive cleansers tin can be used to smooth scratched surfaces. Waxy products like Lemon Pledge and Carnauba cleaner wax actually fill light scratches with wax. However, the wax will reduce your visibility and require reapplication every few days. You lot can also try rubbing alcohol or diluted ammonia. After treating your spectacles with one of these products, shine them with a soft fabric, ideally one fabricated particularly for cleaning glasses.

3. 3

   Preclude hereafter scratches. Lenses are delicate and should be treated with care to prevent them from getting scratched.

   • Use an eyeglass case. A sturdy, cushioned case will protect your eyeglasses; place them in a case rather than in your pocket or throwing them straight into your handbag.^[9]
   • Wash your lenses. Clean your spectacles every day with soapy h2o and dry them with a clean, soft fabric fabricated for this purpose.
   • Stay away from unfriendly products. Some products can harm your lenses and should be avoided. Don't use facial tissues or paper towels to clean your lenses and stay away from anti-bacterial soaps when you wash them.^[10] Be careful when using hairspray, perfume or nail smoothen remover--they can remove the coatings on lenses.

Ad

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertising

Video

• In a compression, the go-to method for fixing a broken bridge is only to wrap record around it to hold the two pieces in place. Choose a color record that matches the color of your frames most closely or make a fashion argument and wrap them in a slice of decorative duct tape.

• Go on glue away from your lenses and your fingers

• If a white residue develops on the frames from contact with acetone, effort rubbing them with an oil based lotion.

Advertisement

• Keep mucilage abroad from optics until completely dry out

Advertizing

About This Article

Commodity Summary X

If you lose a screw from your glasses, endeavour purchasing an eyeglass repair kit from a drugstore. These have replacement screws and a tiny screwdriver to make the repair easy. If you lot can't find a repair kit, push a wooden toothpick through the hinge holes. You can likewise wrap a thin slice of wire through the holes and twist information technology until the temple of your glasses feels secure. If your glasses have a cleaved bridge, keep reading to larn how to fix information technology yourself.

Did this summary help you?

Thanks to all authors for creating a page that has been read 771,963 times.

Did this article assist you lot?

Source: https://www.wikihow.com/Repair-Eyeglasses

Share this post